Jump to content
LegendTrucker56

Euro Truck Simulator All Console Codes

Recommended Posts

 

Exiting the game: If you type "exit" in the Console and press ENTER, you will exit the game. The profile selection screen comes out 

To leave the game completely: If you type "quiet" into the console and press ENTER, you will be completely out of the game. You will close the game with Alt + F4.

 

Returning to the profile screen: If you type "game" in the Console and press ENTER, your profile game is reloaded.

Teleport: To use this you have to have the use 0  camera turned on. After typing "goto" in the console, leave a space and type the name of the city you want to go to. For example ;  ''goto Berlin'' . The free camera will take you there. You can leave your vehicle at any place in the city you are going to. (it only works on single player)

 

Time advance: After typing "g_set_time" in the console, leave a space and type the time you want. For example ;  g_set_time 12 . Time will advance

.

Increase and decrease the volume of the cabin : After writing "s interior volume" in the console, leave a space and type the desired number. The standard number is "1". e.g
Set Free Camera Speed: After typing "g_flyspeed" in the Console, leave a space and type the number you want. The standard number is "100". For example, if you type "g_flyspeed 1000", the free camera speed will increase, if you type "g_flyspeed 50", the free camera speed will decrease.

 

Simulation Speed: After writing "warp" to the Console, leave a space and write the number you want. The standard number is "1". For example, if you type "warp 10", the game will be accelerated. If you type "warp 0.5", the game speed will slow down.

 

If you type "g_minicon 1" in the FPS: Console and press enter, you will see 4-5 lines in the upper left corner of your screen. If you open the console and type "g_fps 1", you can see your FPS on those lines. If you type "0" in place of "1" in this list, you can type "g_fps 0" in the console first and then press enter. Then type "g_minicon 0" and press enter again.

Turn off Traffic Tickets: Type "g_police 0" in the Console and press ENTER. Traffic punishment will be closed. If you change the location of "1" to "0", you can reopen the penalty if you enter console "g_police 1" and press enter.

 

When you’re typing “save”, the game creates a “save from command line” immediately. It’s like a quick save, except your previous save won't be overwritten.

Simple Auto Crossover Time: If you type "g_minicon 1" into the console and press enter, you will see 4-5 lines in the upper left corner of your screen. If you open console and type "g_fps 1", you can see your FPS on those lines. If you type "0" in place of "1" in this list, you can type "g_fps 0" in the console first and then press enter. Then type "g_minicon 0" and press enter again.

 

Weather conditions :

<<< g_set_skybox 1 >>> cloudy

<<< g_set_skybox 1 >>> foggy

<<< g_set_skybox 0 >>> clear without clouds

<<< g_set_weather 1 >>> rainy

<<< g_set_weather 0 >>> sunny

 

 

IMPORTANT NOTE : 

If the console is not active: First we need to activate the console in the game. After I go to My Documents / Euro Truck Simulator 2 folder, we open the config file with the notepad. We use << uset g_console "0" >> in the file and make the place "1" which reads "0". In the map editor we will use << uset g_developer "0" >> in the file and write "1" at the position where it writes "0" because some of the properties that we will use are needed. We enter the game, press the "é" key and open the console. And we're starting to use the following features.

  • Thanks 2
  • Upvote 2

Share this post


Link to post
Share on other sites

Simulation Speed: After writing "warp" to the Console, leave a space and write the number you want. The standard number is "1". For example, if you type "warp 10", the game will be accelerated. If you type "warp 0.5", the game speed will slow down.

 

is it allowed? i dont know if i can modify it a bit so my 90 km/h are the same as my friends because of my computer going to slow

  • Like 1

Share this post


Link to post
Share on other sites

That´s the commands i´ve found and tried out searching the commands list

 

Command                        Description
    
goto (x;y;z)                       (or city name) goto Milano (no Russian characters enabled yet) 
                                           Works with trailer too anytime F9 and
                                           Landing close to the customer (make sure to go slightly over the ground before using F9)

screenshot                       takes a, well, screenshot
g_police 0-1                     set "0" no police, no penalty      
r_mirror_view_distance    eg: 500 is better distance    
uset g_bloom "0"            max clarity

g_traffic 0 - 9.9                0 no traffic and 1 normal traffic (9.9 is max)
g_gallon 0 - 1                   0 is no fuel an 1 is fuel i guess

 

for more realistic behavior 0.5 is officially minimum in game but 0 is hardcore :)
g_suspension_stiffness     0 - 0.5
g_trailer_stability     0 - 0.5
g_truck_stability     0 - 0.5
g_traffic         0 - 1
g_gallon         0 - 1

Share this post


Link to post
Share on other sites

c_krspeed - speed of camera rotation. Worth to increase this speed (if you drive your truck with mouse) to check sides on crossroads faster, because the default value is too slow.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...